Cisco Systems OL-7426-03 Instrukcja Użytkownika Strona 138
- Strona / 276
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
5/26/05 Creating Access Control Lists
OL-7426-03
• Configure port priority on the STP ports using the following command:
>config spanningtree port priority <0-255> <port number>
where <0-255> = STP priority for this port (default priority = 128).
• If required, configure the Cisco Wireless LAN Controller STP bridge priority using the following
command:
>config spanningtree switch bridgepriority <0-65535>
where <0-65535> = STP bridge priority for this Cisco Wireless LAN Controller (default priority
= 32768).
• If required, configure the Cisco Wireless LAN Controller STP forward delay using the following
command:
>config spanningtree switch forwarddelay <4-30>
where <4-30> seconds = STP forward delay for this Cisco Wireless LAN Controller (default
forward delay = 15 seconds).
• If required, configure the Cisco Wireless LAN Controller STP hello time using the following
command:
>config spanningtree switch hellotime <1-10>
where <1-10> seconds = STP hello time for this Cisco Wireless LAN Controller (default hello
time = 2 seconds).
• If required, configure the Cisco Wireless LAN Controller STP maximum age using the following
command:
>config spanningtree switch maxage <6-40>
where <6-40> seconds = STP maximum age for this Cisco Wireless LAN Controller (default =
20 seconds).
• After all the ports have been configured for the desired STP settings, enter the following:
>config spanningtree switch mode enable
This procedure allows the Cisco Wireless LAN Controller to most efficiently set up STP, detect
logical network loops, place redundant ports on standby, and build a network with the most
efficient pathways.
You have configured STP for the Cisco Wireless LAN Controller. Verify that your settings are stored in
memory using the show spanningtree port and show spanningtree switch commands. Continue
with Configuring WLANs
.
Creating Access Control ListsCreating Access Control Lists
When you wish to create Access Control Lists, Cisco WLAN Solution strongly recommends that you use
the Web User Interface. Refer to the Access Control Lists page in the Web User Interface Online Help
document.
- Product Guide 1
- ProductsProducts 2
- Limited Warranty 5
- DISCLAIMER OF WARRANTY 6
- Additional Open Source Terms 7
- Trademarks and Service Marks 7
- Cisco.comCisco.com 8
- Lightweight Access Points 13
- Wireless LAN Controllers 14
- Safety Considerations 16
- 5/26/05 Safety Considerations 29
- Table of Contents 31
- Welcome to the Product Guide! 31
- OVERVIEWS 31
- SOLUTIONS 33
- Operating Location Appliances 36
- REFERENCES 37
- OVERVIEWSOVERVIEWS 39
- • REFERENCES 40
- Operating System Software 45
- Operating System Security 45
- Wireless LAN Controller 48
- External DHCP Servers 51
- Per-WLAN Assignment 51
- Per-Interface Assignment 51
- Security Considerations 51
- Cisco WLAN Solution WLANs 54
- Access Control Lists 54
- Identity Networking 54
- Pico Cell Functionality 56
- Distribution System Ports 61
- AP-Manager Interface 63
- Operator-Defined Interfaces 63
- Service-Port Interface 65
- Startup Wizard 65
- External Antenna Connectors 76
- Antenna Sectorization 76
- Requirements 83
- External Power Supply 83
- Rogue Access Points 85
- Web User Interface 87
- Cisco Wireless Control System 89
- Cisco WCS Base 90
- Floor Plan Editor 92
- SOLUTIONSSOLUTIONS 95
- OverviewOverview 96
- Layer 3 Solutions 97
- Rogue Access Point Solutions 97
- Rogue Access Point Challenges 97
- Using the Web User Interface 104
- Mgmt Via Wireless Interface 110
- Changing the Web Title 114
- Changing the Web Message 114
- Changing the Logo 114
- Preparing the TFTP Server 114
- RADIUS Attributes 118
- Interface-Name 119
- ACL-Name 119
- VLAN-Tag 120
- Tunnel Attributes 120
- 5/26/05 Notes 122
- OL-7426-03 122
- Notes:Notes 122
- TASKSTASKS 123
- Logging Into the CLI 125
- Password: 127
- (system prompt)> 127
- Logging Out of the CLI 128
- CLI Tree Structure 128
- Configuring System Parameters 131
- Time and Date 131
- Users and Passwords 133
- Creating Access Control Lists 138
- Layer 2 Security 141
- WEP Keys 141
- IPSec Authentication 143
- IPSec Encryption 143
- IKE Authentication 143
- IKE Diffie-Hellman Group 143
- Local Netuser 145
- Quality of Service 145
- Activating WLANs 145
- >show serviceport 147
- >config serviceport params 147
- Serial (CLI Console) Port 148
- 802.3x Flow Control 148
- System Logging 148
- Using the Startup Wizard 154
- Locally-Generated Certificate 156
- Saving Configurations 161
- Created 166
- Process: Started messages 166
- Wireless 169
- Wireless Control 171
- Using Cisco WCS 174
- SNMP. . 178
- • Select the Monitor Tab 180
- Using Map Editor 190
- Area Maps 196
- Table - Clients 203
- Locating Clients 208
- Finding Coverage Holes 210
- • Click the Download button 213
- Installing Cisco WCS 214
- Updating the Linux Cisco WCS 216
- Adding User Accounts 219
- Changing Passwords 220
- Deleting User Accounts 220
- Configuring and 225
- Location Appliances 228
- Changing 233
- Are you 236
- WCS Terminal 242
- Appliance using Cisco WCS 242
- • Using Error Messages 245
- • Client Reason Codes 248
- • Client Status Codes 248
- Client Status Codes 249
- REFERENCESREFERENCES 251
- GlossaryGlossary 252
- Exclusion List 258
- Subscriber 266
Powiązane produkty i podręczniki dla Punkty dostępu do sieci WLAN Cisco Systems OL-7426-03
(114 strony)Checkline Series-2 manuali
Manuali dei proprietari e guide per l'utente per Sensori Checkline Series-2.
We fornisce 1 manuali pdf Checkline Series-2 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Komentarze do niniejszej Instrukcji