Cisco Systems PGW 2200 Podręcznik Użytkownika Strona 208
- Strona / 436
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4-26
Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide
OL-18083-01
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software
Configuring the Execution Environment
• Initializing the Provisioning Object Manager, page 4-41
The configuration data file, or XECfgParm.dat file (located in /opt/CiscoMGC/etc/XECfgParm.dat),
lists all the components in the Cisco PGW 2200 Softswitch software and defines how it operates. You
must edit the execution environment parameters in the XECfgParm.dat file to initialize and configure the
Cisco PGW 2200 Softswitch software application. For a complete list of the parameters found in the
XECfgParm.dat file and how they are used by the Cisco PGW 2200 Softswitch, see Appendix A,
“XECfgParm.dat File Parameters.”
For samples of configured XECfgParm.dat files, see the “Sample Configured XECfgParm.dat Files for
Cisco PGW 2200 Softswitch Release 9.8(1)” section on page D-16.
Caution To ensure that your system works as intended, edit only the XECfgParm.dat file parameters which
are listed below, and remember that all parameters are case-sensitive.
Do not modify the processes.dat file. This XECfgParm.dat file should remain unmodified, as delivered
with the Cisco PGW 2200 Softswitch software. If this file is modified, procM may core dump when you
start the Cisco PGW 2200 Softswitch software.
Changing XECfgParm.dat File Parameters
For a complete list of the parameters found in the XECfgParm.dat file and how they are used by the
Cisco PGW 2200 Softswitch, see Appendix A, “XECfgParm.dat File Parameters.”
If you have a fault tolerant system with two Cisco PGW 2200 Softswitch hosts, the XECfgParm.dat files
are different for each host. For examples of these XECfgParm.dat files, see the “Sample Configured
XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1)” section on page D-16.
To change the XECfgParm.dat file parameters, perform the following steps:
Step 1 Log in as root and go to the # prompt.
Step 2 If the Cisco PGW 2200 Softswitch software is running, enter the following command:
# /etc/init.d/CiscoMGC stop
Wait until the system returns the following response:
Signalling procM to shut down
...shutdown complete
Step 3 Change to the /opt/CiscoMGC/etc directory, which contains the XECfgParm.dat file used by your
system.
Step 4 Open the XECfgParm.dat file with any text editor, such as vi.
Step 5 Save your changes and close the editor.
Step 6 Restart the Cisco PGW 2200 Softswitch software by entering the following command:
# /etc/init.d/CiscoMGC start
- Text Part Number: OL-18083-01 1
- CONTENTS 3
- Contents 4
- Document Objectives 9
- Audience 9
- Related Documentation 9
- Document Change History 10
- Installation 11
- Required Software Media 12
- Minimum System Requirements 12
- Required Tasks 13
- Table 1-4 Tasks Checklist 14
- Supported Platforms 15
- Supported Disk Drives 15
- Before You Start 16
- - Selecting package (SUNWifp) 20
- Host” section on page 2-50 26
- 89 blocks 34
- 426 blocks 34
- 8 blocks 34
- SUNWnfscr 43
- SUNWkrbr 43
- /devices-/devicesdevfs-no 45
- Configuring Your Host 64
- SUNWnfscr 85
- SUNWnisu 85
- DO NOT REBOOT 100
- OL-18083-01 104
- (CSCOh026) 117
- Using the SunVTS Test Package 145
- Normal Unit Test 145
- Running a Test in Brief Mode 149
- Running a Test in Full Mode 150
- Manager (ILOM) 152
- Figure 2-1 System Agreement 153
- Figure 2-4 LOM Screen 154
- Start ILOM Using Secure HTTP 157
- An Example of Using ILOM 161
- Serial Console ttya 162
- Cautions, Notes, and Tips 166
- Enter y and press Enter 169
- Enabling Sudo 179
- Installing the License File 179
- Software 183
- Software Directory Structure 185
- % MGC_Setup 190
- Configuring Groups and Users 193
- Basic Tasks 196
- Deleting an SNMP COMMUNITY 201
- Adding a Trap Destination 202
- Deleting a Trap Destination 204
- Activating the New Settings 205
- Specifying IP Addresses 212
- Configuring Engine Parameters 214
- Setting the Call Cutoff Timer 216
- Enabling Call Screening 216
- Configuring Switchover 221
- Configuring SCP Queries 224
- Sample trigger.dat File 227
- .odbc.ini File Information 265
- Setting Up Replication 265
- Network Requirements 266
- Synchronizing Databases 270
- Configuring Cisco ITP-Ls 271
- Configuring the Data Dumper 272
- Migrating to Solaris 10 and 275
- Release 9.8 275
- Cautions and Notes 276
- Required Software 277
- License Installation 277
- Recording System Data 277
- Migration Overview 278
- Installing Sun Solaris 10 282
- Restoring Data Files 283
- Platforms 295
- Live Upgrade Procedure 296
- Falling Back Overview 300
- Release 9.5 or 9.6 301
- Backup Procedure 308
- Restoring the System 309
- LAN Switch Overview 311
- Catalyst 2900 XL Series 312
- Catalyst 5500 and 5000 Series 312
- XECfgParm.dat File Parameters 313
- Special Parameters 314
- Relationships 359
- HP OpenView 363
- Formatting Trap Messages 365
- Step 8 Close the window 366
- Sample Installation Scripts 367
- Sample Uninstall Scripts 413
- Sample LAN Configurations 421
Powiązane produkty i podręczniki dla Oprogramowanie Cisco Systems PGW 2200
(32 strony)Checkline Series-2 manuali
Manuali dei proprietari e guide per l'utente per Sensori Checkline Series-2.
We fornisce 1 manuali pdf Checkline Series-2 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Komentarze do niniejszej Instrukcji