Cisco Systems OL-10426-01 Podręcznik Użytkownika Strona 54
- Strona / 150
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4-8
Cisco WAN Modeling Tools Guide
OL-10426-01, Rev. A0
Chapter 4 Configuration Tables and Fields
Links Table
Keep 1 E Number of existing links. If the Keep
field is 0, the link will be ignored in the
route command and considered for the
optimize commands.
KEEP
*
Since slot, port
are included, this
field is always
set to 1.
*
Used 0 X Shows the size of the node after the
NMT builds a network using the
optimize command.
n/a
Reserve 600/600 O Trunk reserve. Estimate of the
overhead on each link needed for
collecting network statistics and other
administrative overhead. The reserve
size is subtracted from the total link
capacity prior to calculating routes.
The units of statistical reserve can be in
ATM cells (CPs) or Fastpackets (pps).
RESERVE1 /
RESERVE2
*/*
Defaults applied
to links between
BPX switches
and tiered
network feeders.
*/*
Rcv_Rate 0/0 O Receive rate. Largest number of pps or
cps that the node at site 1 can receive
over a link from site 2. The second
field is the largest number of pps or cps
that the node at site 2 can receive over
a link from site 1. Only used for
broadband links (T3/E3) at IGX/IPX
sites, or BXM links. The units are pps
or cps respectively.
If you enter 0 here, the default, NMT
will set this field to the highest value
possible for the card. Rcv_Rate
supported on the AIT, ALM, BTM,
and BXM card.
BB_MAX1 /
BB_MAX2
*/* */*
Red N P Redundancy. Specifies whether site has
redundant components. Y—site has
redundant components. N—sites does
not have redundant components.
RED
VT_Rate&
Type
0 O Virtual Trunk Rate. Bandwidth of the
trunk in cells per second. (VTs must
have VT in media field.)
VT_RATE
**
Traffic Blank 0 Types of traffic allowed on this link. If
blank, all types are allowed.
TRAFFIC
LRd N O Link redundancy. Y—spare trunk is
used on redundant link (for BPX to
IBX/IPX links only). N—spare trunk is
not used on redundant link.
BACKUP
Dist 0 E Distance between sites in miles or
kilometers. Must be consistent with the
Line Cost table in the Maintenance
menu.
DIST
Table 4-3 Link Table (continued)
Field Defaults Notes Description and Comments DBF CET TPI
- Customer Order Number: 1
- Text Part Number: OL-10426-01 1
- CONTENTS 3
- 3 Using the NMT 3-1 4
- 5 NMT Execute Commands 5-1 5
- 6 NMT Reports 6-1 5
- 8 NMT Map 8-1 6
- 11 SpreadSheet Interface 11-1 7
- Contents 8
- Obtaining Documentation 10
- Documentation Feedback 11
- Submitting a Service Request 13
- Functionality of the NMT 18
- Gaps 21
- Data Translation Tools 22
- System Requirements 23
- Installing the NMT 24
- Creating a Working Directory 25
- Installing the NMT 26
- Upgrading the NMT Software 28
- Starting the NMT 28
- Removing NMT 29
- Removing Sub-applications 31
- Using the NMT 33
- NMT Menu Bar 34
- File Menu 35
- Configure Menu 36
- Chapter 3 Using the NMT 37
- File Menu 37
- Utilities 38
- Edit Options 38
- Display Menu 39
- Report Menu 40
- Keyboard Commands 41
- Table 3-1 Sun Key Assignments 42
- Key Function Description 42
- Modeling Processes 43
- Error Checking 44
- Troubleshooting NMT 45
- Troubleshooting NMT 46
- General Table Information 47
- Sites Table 48
- Sites Table 49
- Y- for feeder; 50
- N- for router 50
- Links Table 52
- Minimal Link Table Usage 53
- Links Table 54
- Link Special Cases 56
- Voice Table 57
- Voice Table 58
- Data Table 60
- Data Table 61
- Bursty Table 63
- Table 4-8 Bursty Table 64
- Bursty Table 65
- Bursty Table Special Cases 69
- Interface Table 70
- Interface Table 71
- Feeder Table 72
- Card Table 73
- Groups and Network Table 74
- Nodes Table 75
- Network Settings 75
- Network Settings 76
- Model Options 77
- Modeling Implicit Feeders 78
- Feeders 79
- Modeling Explicit Feeders 80
- Obsolete Products 81
- Obsolete Products 82
- FastPAD 84
- Port Concentrator 87
- Tiered Networks 88
- NMT Execute Commands 89
- Preferred and Directed Routes 90
- PNNI Routing 91
- Fail Analysis Command 92
- Build Sites Command 92
- Optimize Command 93
- NMT Command Results 94
- Optimize Command 95
- NMT Reports 97
- Link Load Report 98
- Connection Routes Report 99
- Failed Connections Report 99
- Parts List Report 100
- Using the Map Tool 101
- OL-10426-01, Rev. A0 102
- Chapter 6 NMT Reports 102
- Using the Map Tool 102
- Creating a Graphical Display 103
- NMT Utilities Command Line 105
- NMT Map 107
- Chapter 8 NMT Map 108
- NMT Map Startup 108
- Zooming the Map 112
- Panning the Map 113
- Map Color Coding 113
- NMT Map Main Menu 114
- NMT Map Main Menu 115
- Adding New Groups 116
- Deleting Groups 118
- Saving Your Work 119
- Retrieving Map Data Into NMT 120
- Configuration Extraction Tool 121
- Using the CET 122
- Step 4 This step is optional 123
- Other CET Commands 124
- Troubleshooting CET 125
- Troubleshooting CET 126
- Remote CET Extracts 128
- Remote CET Extracts 129
- Troubleshooting 130
- Probable 131
- Solution 131
- WANDL — Third-Party Interface 133
- WANDL_directory 136
- SpreadSheet Interface 137
- NMT to Microsoft Excel 139
- Microsoft Excel to NMT 140
- Usage Review 141
- SSI TroubleShooting 142
- CND PC Import Utilities 143
- CND PC Import Utilities 144
- CND PC Utilities 146
Powiązane produkty i podręczniki dla Oprogramowanie Cisco Systems OL-10426-01
(220 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji