Cisco Systems Network Device 2800 Instrukcja Instalacji

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 U

10Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Cisco 90-Day Limited Hardware Warranty TermsCisco 90-Day Limited Hardwar

2Troubleshooting Cisco 2800 Series RoutersOL-5789-01 Solving ProblemsSolving ProblemsThe key to solving problems is to isolate the problem to a speci

3Troubleshooting Cisco 2800 Series RoutersOL-5789-01 Solving Problems• Does the router shut down after being on a short time?–Check for an environmen

4Troubleshooting Cisco 2800 Series RoutersOL-5789-01 Reading System LEDs–Make sure that you have a version of Cisco IOS software that supports the mo

5Troubleshooting Cisco 2800 Series RoutersOL-5789-01 Reading System LEDsTable 1 System LEDs on Cisco 2800 Series RoutersLED Indicator State Meaning

6Troubleshooting Cisco 2800 Series RoutersOL-5789-01 Reading Port and Module LEDsReading Port and Module LEDsThe port and module LEDs, located on the

7Troubleshooting Cisco 2800 Series RoutersOL-5789-01 System MessagesSystem MessagesThis section describes system error and recovery messages that may

8Troubleshooting Cisco 2800 Series RoutersOL-5789-01 System MessagesThe terminal should display one of the following prompts:Router> (indicates th

9Troubleshooting Cisco 2800 Series RoutersOL-5789-01 System Messages— — Error:%ENVMON-3-FAN_FAILED: Fan fan-number not rotating.Explanation:The speci

10Troubleshooting Cisco 2800 Series RoutersOL-5789-01 System MessagesAUX/PWRAmber Message:%ENVMON-5-RPS_STATUS: RPS standby/faultyExplanation:Redunda

11Troubleshooting Cisco 2800 Series RoutersOL-5789-01 Recovering a Lost PasswordRecovering a Lost PasswordYou can recover a lost enable password, but

11Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Obtaining DocumentationNote You must have Adobe Acrobat Reader to view a

12Troubleshooting Cisco 2800 Series RoutersOL-5789-01 More Troubleshooting Help—Cisco Technical Assistance Center

13Troubleshooting Cisco 2800 Series RoutersOL-5789-01 More Troubleshooting Help—Cisco Technical Assistance CenterCopyright © 2004 Cisco Systems, Inc.

14Troubleshooting Cisco 2800 Series RoutersOL-5789-01 More Troubleshooting Help—Cisco Technical Assistance Center

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

2Installing Network Modules in Cisco 2800 Series RoutersOL-5790-01 Installing Slot Dividers in Network Module SlotsInstalling Slot Dividers in Networ

3Installing Network Modules in Cisco 2800 Series RoutersOL-5790-01 Installing Slot Dividers in Network Module SlotsFigure 3 Tightening the Slot Divid

4Installing Network Modules in Cisco 2800 Series RoutersOL-5790-01 Installing and Removing Filler Panels in Network Module SlotsInstalling and Removi

5Installing Network Modules in Cisco 2800 Series RoutersOL-5790-01 Installing and Removing Filler Panels in Network Module SlotsFigure 6 Filler Panel

6Installing Network Modules in Cisco 2800 Series RoutersOL-5790-01 Installing and Removing Filler Panels in Network Module SlotsFigure 8 Filler Panel

7Installing Network Modules in Cisco 2800 Series RoutersOL-5790-01 Installing Blank Panels over Empty Chassis SlotsInstalling Blank Panels over Empty

12Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Documentation FeedbackCisco.comYou can access the most current Cisco doc

8Installing Network Modules in Cisco 2800 Series RoutersOL-5790-01 Related Product DocumentationCopyright © 2004 Cisco Systems, Inc. All rights reser

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

2Installing Interface Cards in Cisco 2800 Series RoutersOL-5791-01Installing and Removing Slot DividersInstalling Slot Dividers in HWIC Slots on Cisco

3Installing Interface Cards in Cisco 2800 Series RoutersOL-5791-01Installing and Removing Slot DividersFigure 2 Inserting a Slot Divider into an HWIC

4Installing Interface Cards in Cisco 2800 Series RoutersOL-5791-01Installing and Removing Slot DividersFigure 3 Slot Divider for HWIC Slots on Cisco 2

5Installing Interface Cards in Cisco 2800 Series RoutersOL-5791-01Installing and Removing Slot DividersFigure 5 Slot Divider Installed in an HWIC Slot

6Installing Interface Cards in Cisco 2800 Series RoutersOL-5791-01Installing Blank Panels over Empty Chassis SlotsFigure 6 Squeeze the Slot Divider to

7Installing Interface Cards in Cisco 2800 Series RoutersOL-5791-01Related Product DocumentationBlank Panels for HWIC SlotsThe high-speed WAN interface

8Installing Interface Cards in Cisco 2800 Series RoutersOL-5791-01Related Product DocumentationCopyright © 2004 Cisco Systems, Inc. All rights reserve

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

13Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Obtaining Technical AssistanceCisco Technical Support WebsiteThe Cisco T

2Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Removing the Chassis CoverWarningBefore working on a system that ha

3Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Removing the Chassis CoverFigure 1 Removing the Cisco 2801 Chassis

4Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Removing the Chassis CoverFigure 3 Removing the Cisco 2801 Chassis

5Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Removing the Chassis CoverStep 4 Perform the following steps to loo

6Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Removing the Chassis CoverStep 6 Lift the cover free of the router

7Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Removing the Chassis CoverRemoving the Cover from Cisco 2821 and Ci

8Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Removing the Chassis CoverFigure 7 Cisco 2821 or Cisco 2851 Router—

9Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Locating ModulesLocating ModulesFigure 8 shows the locations of the

10Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Locating ModulesFigure 9 Module Locations in Cisco 2811 Routers1 A

11Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Locating ModulesFigure 10 Module Locations in Cisco 2821 Router1 A

14Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Obtaining Additional Publications and InformationObtaining Additional Pu

12Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing DRAM DIMMsFigure 11 Module Locations in Ci

13Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing DRAM DIMMsCaution Handle DRAM DIMMs by the

14Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing DRAM DIMMsFigure 13 Removing a DRAM DIMMSt

15Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing DRAM DIMMsFigure 15 Installing a DIMMStep

16Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsFigure 16 Installing a DRAM DIMMStep 6

17Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsSoftware Requirement for AIMsCisco IOS

18Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsStep 3 Carefully lift the AIM free fro

19Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsFigure 18 Connecting the AIM to the Ci

20Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsStep 3 Install the two machine-thread

21Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsStep 7 Check that the AIM is installed

15Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Obtaining Additional Publications and Information

22Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsFigure 22 Removing Screws from System

23Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsFigure 23 Connecting an AIM to the Sys

24Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsStep 7 Check that the AIM is installed

25Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsInstalling a CompactFlash Memory Card

26Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsFigure 26 CompactFlash Memory Card Ins

27Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing AIMsFigure 27 Example of an AIM Label Loca

28Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing PVDMsThe following example shows one Compr

29Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing PVDMsPVDM Location and OrientationThe PVDM

30Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing and Removing PVDMsFigure 29 Removing a PVDMStep 3Place

31Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 30 Installing a PVDMStep 4If you

16Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Obtaining Additional Publications and InformationCopyright © 2004 Cisco

32Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 31 Cisco 2801 Main Power Supply R

33Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 32 Inserting the ILP Supply into

34Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyRemoving the Existing Power SupplyTo rem

35Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyStep 3 Remove the power supply retention

36Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyInstalling an AC-Input Power SupplyThe A

37Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 36 Connecting a Primary Power Cab

38Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyInstalling a DC-Input Power SupplyThe DC

39Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 38 Connecting a Secondary Power C

40Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyInstalling an ILP SupplyThe ILP supply h

41Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 40 Connecting an ILP Cable in a C

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

42Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyRemoving the Existing Power SupplyTo rem

43Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 42 Removing the Bezel from a Cisc

44Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyStep 2 Remove the two power supply retai

45Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 44 Removing the Power Supply from

46Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyStep 1 Insert the AC-input power supply

47Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyInstalling a DC-Input Power SupplyThe DC

48Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 48 Connecting a Secondary Power C

49Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyInstalling an ILP SupplyThe ILP supply h

50Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Replacing the Power SupplyFigure 50 Connecting an ILP Cable in Cis

51Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing the Chassis CoverInstalling the Chassis CoverCisco 2801

2Overview of Cisco 2800 Series RoutersOL-5783-01 Hardware FeaturesFigure 2 Front View of a Cisco 2811 RouterFigure 3 Front View of a Cisco 2821 or Ci

52Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing the Chassis CoverInstalling the Cover on Cisco 2811 Rou

53Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing the Chassis CoverInstalling the Cover on Cisco 2821 and

54Installing and Upgrading Internal Modules in Cisco 2800 Series RoutersOL-5792-04 Installing the Chassis CoverCopyright © 2004, 2005 Cisco Systems,

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

2Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series RoutersOL-5793-01 Installing a CompactFlash Memory CardCaution Do not remove

3Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series RoutersOL-5793-01 Installing a CompactFlash Memory CardCaution To prevent dam

4Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series RoutersOL-5793-01 Installing a CompactFlash Memory CardCopyright © 2004 Cisco

3Overview of Cisco 2800 Series RoutersOL-5783-01 Hardware FeaturesFigure 4 Serial Number Location on the Cisco 2801 RouterNote The serial number for

2Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 AudienceThese documents describe several router platforms that are simila

4Overview of Cisco 2800 Series RoutersOL-5783-01 Hardware FeaturesThe serial number label for Cisco 2821 and Cisco 2851 routers is located on the rea

5Overview of Cisco 2800 Series RoutersOL-5783-01 Hardware FeaturesRemovable and Interchangeable ModulesTable 2 summarizes the optional modules that c

6Overview of Cisco 2800 Series RoutersOL-5783-01 Hardware FeaturesMemoryCisco 2800 series routers contain the following types of memory:• DRAM—Stores

7Overview of Cisco 2800 Series RoutersOL-5783-01 Hardware FeaturesPowerTable 4 summarizes the power options for Cisco 2800 series routers. Cisco 2801

8Overview of Cisco 2800 Series RoutersOL-5783-01 Hardware FeaturesTo see descriptions of LEDs in removable modules and interface cards, refer to the

9Overview of Cisco 2800 Series RoutersOL-5783-01 Hardware FeaturesTable 6 Summary of Cisco 2811, Cisco 2821, and Cisco 2851 Series LED IndicatorsLED

10Overview of Cisco 2800 Series RoutersOL-5783-01 Chassis ViewsChassis VentilationInternal multispeed fans provide chassis cooling, controlled by an

11Overview of Cisco 2800 Series RoutersOL-5783-01 Chassis ViewsFigure 7 Front Panel of the Cisco 2801 RouterDouble-wide HWICs can go into slots 0 and

12Overview of Cisco 2800 Series RoutersOL-5783-01 Chassis ViewsCisco 2811 ChassisFigure 9, Figure 10, and Figure 11 show the front panel of a Cisco 2

13Overview of Cisco 2800 Series RoutersOL-5783-01 Chassis ViewsFigure 11 Front Panel of Cisco 2811 Router with DC Input PowerFigure 12 Rear Panel of

3Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 ConventionsConventionsThese documents use the conventions listed in Table

14Overview of Cisco 2800 Series RoutersOL-5783-01 Chassis ViewsCisco 2821 and Cisco 2851 ChassisFigure 13, Figure 14, and Figure 15 show the front pa

15Overview of Cisco 2800 Series RoutersOL-5783-01 Chassis ViewsFigure 15 Front Panel of Cisco 2821 and Cisco 2851 Routers with DC Input PowerFigure 1

16Overview of Cisco 2800 Series RoutersOL-5783-01 Interface NumberingFigure 17 Rear Panel of the Cisco 2851 RouterInterface NumberingTable 7 summariz

17Overview of Cisco 2800 Series RoutersOL-5783-01 Interface NumberingNote On the Cisco 2801 router, the numbering format for configuring an asynchron

18Overview of Cisco 2800 Series RoutersOL-5783-01 SpecificationsNote On the Cisco 2811, Cisco 2821, and Cisco 2851 routers, the interface numbering s

19Overview of Cisco 2800 Series RoutersOL-5783-01 SpecificationsOperating humidity 5 to 95%, noncondensingOperating temperature 32 to 104° F (0 to 40

20Overview of Cisco 2800 Series RoutersOL-5783-01 SpecificationsTable 10 Cisco 2811 Router SpecificationsDescription SpecificationDimensions (H x W x

21Overview of Cisco 2800 Series RoutersOL-5783-01 SpecificationsEMC compliance FCC Part 15; ICES-003 Class A; EN55022 Class A; CISPR22 Class A; AS/NZ

22Overview of Cisco 2800 Series RoutersOL-5783-01 SpecificationsTable 11 Cisco 2821 Router SpecificationsDescription SpecificationDimensions (H x W x

23Overview of Cisco 2800 Series RoutersOL-5783-01 SpecificationsEMC compliance FCC Part 15; ICES-003 Class A; EN55022 Class A; CISPR22 Class A; AS/NZ

4Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Safety WarningsSafety WarningsSafety warnings appear throughout these pub

24Overview of Cisco 2800 Series RoutersOL-5783-01 SpecificationsTable 12 Cisco 2851 Router SpecificationsDescription SpecificationDimensions (H x W x

25Overview of Cisco 2800 Series RoutersOL-5783-01 Regulatory ComplianceRegulatory ComplianceFor compliance information, refer to the Cisco 2800 and C

26Overview of Cisco 2800 Series RoutersOL-5783-01 Regulatory ComplianceCopyright © 2004 Cisco Systems, Inc. All rights reserved.CCVP, the Cisco Logo,

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

2Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 Safety Recommendations• Wear safety glasses when working under con

3Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 General Site RequirementsPreventing Electrostatic Discharge Damage

4Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 General Site RequirementsSite EnvironmentCisco 2800 series routers

5Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 General Site RequirementsSite ConfigurationThe following precautio

6Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 Installation ChecklistInstallation ChecklistThe sample installatio

7Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 Creating a Site LogCreating a Site LogThe Site Log provides a reco

5Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Safety WarningsWarnungWICHTIGE SICHERHEITSANWEISUNGENDieses Warnsymbol be

8Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 Required Tools and Equipment for Installation and MaintenanceInspe

9Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 Required Tools and Equipment for Installation and Maintenance

10Preinstallation Requirements and Planning for Cisco 2800 Series RoutersOL-5784-01 Required Tools and Equipment for Installation and MaintenanceCopy

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 U

2Port and Cable Information for Cisco 2800 Series RoutersOL-5785-01 Preparing to Connect to a NetworkThe default parameters for the console port are

3Port and Cable Information for Cisco 2800 Series RoutersOL-5785-01 Preparing to Connect to a NetworkEthernet ConnectionsThe IEEE has established Et

4Port and Cable Information for Cisco 2800 Series RoutersOL-5785-01 Preparing to Connect to a NetworkSignaling Standards SupportedThe synchronous se

5Port and Cable Information for Cisco 2800 Series RoutersOL-5785-01 Preparing to Connect to a NetworkBalanced drivers allow EIA/TIA-449 signals to t

6Port and Cable Information for Cisco 2800 Series RoutersOL-5785-01 Preparing to Connect to a NetworkFor more information on BRI WAN interface cards

Corporate Headquarters:© 2005 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USAChassis

6Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Safety WarningsVarning!VIKTIGA SÄKERHETSANVISNINGARDenna varningssignal s

2Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Installing Modules and Interface Cards• Quick Start Guide: Network Modules

3Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Installing Modules and Interface CardsFigure 2 Chassis Slot Locations in Ci

4Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Installing Internal Field-Replaceable Units (FRUs)Figure 4 Chassis Slot Loc

5Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Setting Up the ChassisFor Installing CompactFlash Memory Cards• The “Instal

6Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Setting Up the ChassisCisco 2811, Cisco 2821, and Cisco 2851 routers can be

7Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Setting Up the ChassisAttaching Rack-Mount Brackets to Cisco 2801 RoutersUs

8Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Setting Up the ChassisFigure 10 Bracket Installation for Rear MountingFigur

9Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Setting Up the ChassisWarningTo prevent personal injury or damage to the ch

10Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Setting Up the ChassisFigure 13 Attaching the Optional Cable Management Br

11Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Setting Up the ChassisCaution Do not place anything on top of the router t

7Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Safety WarningsAvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇAEste símbolo de av

12Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Setting Up the ChassisAttaching the Router to a WallAttach the router to t

13Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Installing the Chassis Ground ConnectionInstalling the Chassis Ground Conn

14Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Installing the Chassis Ground ConnectionTo install the ground connection f

15Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Installing the Chassis Ground ConnectionFigure 20 NEBS-Compliant Chassis G

16Chassis Installation Procedures for Cisco 2800 Series RoutersOL-5786-03 Installing the Chassis Ground Connection

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

2Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Power ConnectionsPower ConnectionsThis section explains how to connect AC or DC

3Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Power ConnectionsWarningThis product relies on the building’s installation for s

4Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Power ConnectionsWiring Procedure for DC InputTo connect a router to a DC power

5Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Power ConnectionsFigure 1 DC Power Connections for Cisco 2800 Series Routers Ste

8Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Safety Warnings

6Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Power ConnectionsFigure 3 Wire Routing and Attachment for Cisco 2821 and Cisco 2

7Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Power ConnectionsIn Figure 4, either the positive source terminal or the negativ

8Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Power ConnectionsFigure 6 Connecting Source A and Source B with Common Positive

9Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Connecting WAN, LAN, and Voice CablesConnecting Routers to Backup PowerIf your r

10Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Connecting WAN, LAN, and Voice CablesPorts and CablingTable 3 summarizes some t

11Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Connecting WAN, LAN, and Voice CablesTable 3 WAN, LAN, and Voice ConnectionsPor

12Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Connecting to a Console Terminal or ModemConnection Procedures and PrecautionsC

13Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Connecting to a Console Terminal or ModemConnecting to the Console PortIf a con

14Cable Connection Procedures for Cisco 2800 Series RoutersOL-5787-02 Connecting to a Console Terminal or ModemCopyright © 2004 Cisco Systems, Inc. A

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US

9Cisco 2800 Series Hardware Documents: Introduction and WarningsOL-5808-01 Related DocumentationRelated DocumentationThe Cisco IOS software running

2Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Powering Up Cisco 2800 Series Routers• The external CompactFla

3Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Powering Up Cisco 2800 Series RoutersYou may see different sta

4Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Configuring the RouterVerifying the Hardware ConfigurationTo d

5Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Configuring the RouterNote If you need help with the interface

6Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Configuring the RouterStep 1 To proceed using the setup comman

7Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Configuring the RouterFastEthernet0/1 unassigned

8Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Configuring the RouterInitial Configuration Using the Cisco CL

9Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Configuring the RouterVerifying the Initial ConfigurationVerif

10Power Up and Initial Configuration Procedures for Cisco 2800 Series RoutersOL-5788-01 Configuring the RouterCopyright © 2004 Cisco Systems, Inc. Al

Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 US