Cisco Systems C2960XSTACK Instrukcja Użytkownika Strona 108
- Strona / 112
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
SPAN and RSPAN Configuration Examples
Example: Configuring Local SPAN
This example shows how to set up SPAN session 1 for monitoring source port traffic to a destination port.
First, any existing SPAN configuration for session 1 is deleted, and then bidirectional traffic is mirrored from
source Gigabit Ethernet port 1 to destination Gigabit Ethernet port 2, retaining the encapsulation method.
Switch(config)# no monitor session 1
Switch(config)# monitor session 1 source interface gigabitethernet1/0/1
Switch(config)# monitor session 1 destination interface gigabitethernet1/0/2
encapsulation replicate
Switch(config)# end
This example shows how to remove port 1 as a SPAN source for SPAN session 1:
Switch(config)# no monitor session 1 source interface gigabitethernet1/0/1
Switch(config)# end
This example shows how to disable received traffic monitoring on port 1, which was configured for bidirectional
monitoring:
Switch(config)# no monitor session 1 source interface gigabitethernet1/0/1 rx
The monitoring of traffic received on port 1 is disabled, but traffic sent from this port continues to be monitored.
This example shows how to remove any existing configuration on SPAN session 2, configure SPAN session
2 to monitor received traffic on all ports belonging to VLANs 1 through 3, and send it to destination Gigabit
Ethernet port 2. The configuration is then modified to also monitor all traffic on all ports belonging to VLAN
10.
Switch(config)# no monitor session 2
Switch(config)# monitor session 2 source vlan 1 - 3 rx
Switch(config)# monitor session 2 destination interface gigabitethernet1/0/2
Switch(config)# monitor session 2 source vlan 10
Switch(config)# end
This example shows how to remove any existing configuration on SPAN session 2, configure SPAN session
2 to monitor received traffic on Gigabit Ethernet source port 1, and send it to destination Gigabit Ethernet
port 2 with the same egress encapsulation type as the source port, and to enable ingress forwarding with IEEE
802.1Q encapsulation and VLAN 6 as the default ingress VLAN:
Switch(config)# no monitor session 2
Switch(config)# monitor session 2 source gigabitethernet1/0/1 rx
Switch(config)# monitor session 2 destination interface gigabitethernet1/0/2 encapsulation
replicate ingress dot1q vlan 6
Switch(config)# end
This example shows how to remove any existing configuration on SPAN session 2, configure SPAN session
2 to monitor traffic received on Gigabit Ethernet trunk port 2, and send traffic for only VLANs 1 through 5
and VLAN 9 to destination Gigabit Ethernet port 1:
Switch(config)# no monitor session 2
Switch(config)# monitor session 2 source interface gigabitethernet1/0/2 rx
Switch(config)# monitor session 2 filter vlan 1 - 5 , 9
Catalyst 2960-X Switch Network Management Configuration Guide, Cisco IOS Release 15.0(2)EX
96 OL-29044-01
Configuring SPAN and RSPAN
SPAN and RSPAN Configuration Examples
- Cisco IOS Release 15.0(2)EX 1
- CONTENTS 3
- Contents 4
- OL-29044-01 v 5
- OL-29044-01 vii 7
- Document Conventions 9
- Timesaver 10
- Related Documentation 11
- Command Modes 13
- Table 1: Command Mode Summary 14
- Using the Help System 15
- CLI Error Messages 16
- Configuration Logging 17
- Recalling Commands 18
- 12 OL-29044-01 24
- Finding Feature Information 25
- 14 OL-29044-01 26
- Configuration Service 27
- Event Service 28
- NameSpace Mapper 28
- DeviceID 29
- Hostname and DeviceID 29
- Cisco IOS CNS Agents 30
- Automated CNS Configuration 31
- Enabling the CNS Event Agent 32
- What to Do Next 33
- Before You Begin 34
- Refreshing DeviceIDs 40
- Monitoring CNS Configurations 43
- Additional References 44
- Information About CDP 45
- How to Configure CDP 46
- Disabling CDP 48
- Enabling CDP 49
- Disabling CDP on an Interface 50
- Enabling CDP on an Interface 51
- 42 OL-29044-01 54
- Protocol 55
- 44 OL-29044-01 56
- Prerequisites for SNMP 56
- OL-29044-01 45 57
- Restrictions for SNMP 58
- Information About SNMP 58
- SNMP Agent Functions 59
- SNMP Community Strings 59
- SNMP MIB Variables Access 59
- SNMP Notifications 60
- Default SNMP Configuration 61
- SNMP Configuration Guidelines 61
- How to Configure SNMP 62
- Configuring Community Strings 63
- 56 OL-29044-01 68
- OL-29044-01 57 69
- Monitoring SNMP Status 74
- SNMP Examples 75
- Management Protocol 76
- 66 OL-29044-01 78
- SPAN and RSPAN 80
- Remote SPAN 81
- 70 OL-29044-01 82
- SPAN Sessions 83
- Monitored Traffic 83
- Source Ports 84
- Source VLANs 85
- VLAN Filtering 85
- Destination Port 85
- RSPAN VLAN 86
- OL-29044-01 75 87
- Flow-Based SPAN 88
- Configuration Guidelines 89
- Creating a Local SPAN Session 90
- Specifying VLANs to Filter 94
- SUMMARY STEPS 100
- DETAILED STEPS 100
- Example: 101
- Configuring an FSPAN Session 103
- Configuring an FRSPAN Session 105
- Configuring SPAN and RSPAN 110
- 98 OL-29044-01 110
- OL-29044-01 IN-1 111
- IN-2 OL-29044-01 112
Powiązane produkty i podręczniki dla Networking Cisco Systems C2960XSTACK
(32 strony)Checkline Series-2 manuali
Manuali dei proprietari e guide per l'utente per Sensori Checkline Series-2.
We fornisce 1 manuali pdf Checkline Series-2 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Komentarze do niniejszej Instrukcji